Bont Inline SkatesBont Inline Skates

Bont Molding Socks

Bont has been creating custom skates since 1975 and is the world’s largest producer of custom made skates producing up to 120 pairs per week. In the mid 90’s Mr. Inze Bont tried molding socks to create a mold of skater’s feet and found it to be simple, clean and light weight for shipping.

Before we start, make sure you have these items.

Bont Molding Socks-Tools
  • The correct size molding socks. The socks come in Small Medium and Large
  • A bucket of cold water
  • Rubber gloves
  • Masking tape
  • Special scissors that came with the molding pack
  • 2 long plastic bags
  • 1 black plastic protective strip
  • A permanent marker
Bont Molding Socks-standing

The first thing you need to do is to make sure that your Achilles tendon is straight when you are molding. To achieve this, get someone to stand behind you while you move your feet further apart or closer together until they are straight. Usually, your feet should be shoulder width apart. When you get them in the right place, remember to keep your feet in that position when you are molding them.

Bont Molding Socks-right method

Make sure that you keep your heals on the ground with your weight slightly forward. Don’t lean on any objects while molding. It is very important that you are standing up while molding. Do not sit down. Make sure that you have a flat hard surface to stand on. Do not stand on any soft materials while you mold your feet.

Bont Molding Socks-Step1

Let’s begin. Take the protective strip and place it on the front of the foot in line with the big toe. Tape it to the foot in 3 places.

Bont Molding Socks-Step2

Next, place the plastic bag over the foot and put your gloves on.

Bont Molding Socks-Step3

The sock reacts with moisture in the air so don’t open it until you are ready to use it. It will set quickly. Open the sock and dip it in the bucket of water making sure it is wet. Turn the sock inside out so that the smooth part is against your foot.

Bont Molding Socks-Step4

Put the sock on making sure that the seam is on top of the toes and that the sock is pulled all the way up.

Bont Molding Socks-Step5

Make a small cut in the bottom of the sock on top of the black protective strip so it will be easier to take off later.

Bont Molding Socks-Step6

Make a second cut at the top of the sock.

Bont Molding Socks-Step7

Wet your hands and begin to rub the sock. Pay special attention to the Achilles tendon and the arch of the foot. Make sure the person is standing with their feet apart so that their Achilles tendon is straight like we tested earlier. The socks will begin to heat up and they may become quite hot for a minute or so. The resin will react with the water and begin bubbling.

Bont Molding Socks-Step8

Keep putting water on your hands and rubbing the sock up and down to make it fit close to the foot. After about 5 minutes, the sock will cool down and become hard. If you are not sure if it is hard enough, just leave it to set for another minute.

Bont Molding Socks-Step9

Use the special scissors to cut along the black protective strip and cut the sock off. Then open the stock and the foot will slip out. Pull the plastic out of the sock if it has remained inside.

Bont Molding Socks-Step10

Hold the sock together and tape it up.

Bont Molding Socks-Step11

Use a permanent marker to mark any foot problems that we should look out for such as bunions or spurs on your feet. Write your name on the bottom of the mold.

Bont Molding Socks-Step12

Your completed mold should look like this. If it doesn’t, then it is better to make a new one than to send us a bad mold.

Dry the socks and pack them in foam, bubble wrap or newspaper to ship to us. Make sure they are packed well so they are not damaged in transit.