Cheetah

value for money

The Bont Cheetah brings new meaning to the term 'value for money' for an inline skate. This is a fully heat moldable, light weight fiberglass racing boot that is loaded with features.

This boot is made by hand using Bont's monocoque manufacturing technique. Each layer of fiberglass is hand laid in different directions before being painted with resin and then bandaged extremely tight to remove any excess resin. The boot is then baked in the oven for 45 minutes for curing. The light weight outer skin is then stitched and glued to the base.

Buy Now

  • Cheetah White
  • Cheetah Black
  • Cheetah White/S-Frame/G3
  • Cheetah Black/S-Frame/G3
  • Cheetah Black 3PT/3PF/G3
  • Cheetah Black 2PT/3PF/HR
  • Cheetah White 2PT/3PF/HR

Click on images above

Anti Stretch

Between the outer skin and the liner we add a material that is proprietary to Bont to stop the boot from stretching over time. This material has similar strength characteristics to Kevlar. This material is stitched to the outer skin and bonded to the liner so it can never move or be removed, it becomes part of the boots structure. This layer is the reason that Bont boots do not stretch out as much as other brands of boots over time.

Anti Stretch

Last Design

A last is a plastic replica of a foot that the boot is built around. Last makers do not make skate lasts, they only make shoe lasts so perfecting a speed skating last is not an easy prospect. At Bont, we have been perfecting our lasts since 1975 and the process is ongoing. We feel that we put more effort into our last than any other skating brand and it is the reason that Bont boots fit more skaters than any other brand on the market.

Last Design

Padding

The Cheetah utilises closed cell memory foam that will not retain water assisting in maintaining a lighter shoe during wet conditions as well as ensuring sweat which can begin to break down the durability of the shoe is not absorbed.

Padding

Heat Moulding

Bont skates are the most heat moldable skates on the market. Our resin is developed in house and has been perfected over 36 years to be an extremely stiff resin that becomes pliable at relatively low temperatures. You may have tried heat molding other brands of boots and found that you needed to increase the temperature to try to get it to mold. That is not the case with your Bont boots and we urge you to start with low temperatures.

Specification

Model Cheetah
Base 100% hand laid fiberglass
Outer Skin Microfiber
Liner Microfiber liner
Pitch 12mm
Air Vents Tongue
Heat Moldable Fully Heat Moldable Base Utilizing Epoxy Thermoset Resin
Padding Soft Memory Foam
Buckle Microadjustable
Size Options 3 - 13
Fit Options Standard, Narrow, Wide
Inline

Welcome to the Bont Size Wizard

The best way to find out what BONT size you are is to try one on.

If you are unable to do this, please get the right BONT size by following bont sizing wizard step by step.

Please prepare a piece of paper, a pen, a ruler, then click 'start' when you are ready

 

Step1. Put a piece of paper against the wall

Step2. Place your heel to touch the wall

Step3. Place your toe at the longest distance from the wall

Step4. Mark the end of your toe on the paper

Step5. Mark the widest part of your foot on the paper

Step6. Then measure the length and width

Step7. Enter in your MM size in the box, then press the "GO"

Left Foot
mm
mm
Right Foot
mm
mm
Left Foot
Right Foot
Bont
Euro
*Note that this wizard is a guide and may not work with all feet.
Standard Buckle Kit

Standard Buckle Kit

Need to replace your buckle? This buckle kit includes a pair of buckles, loop, a pair of 8cm ladders and screws. Just grab a small screw driver and you can easily replace your current buckles.

Please note that you can only replace the buckle on your shoe with the same buckle kit that the shoe came with. You can not replace a Standard buckle with a Slimline buckle.

Buy Now
Protective front bumper

Protective front bumper

This extremely durable and super light TPU protective bumper can provide extra protection and style for your skates. Simply glue them on the outside of the skates with Loctite 401.

A set of 2 bumpers (Left and Right)

Buy Now
Bont Laces-Optional color

Bont Laces-Optional color

Buy Now
Standard Buckle Kit

Bont Innersole for inline

Bont innersoles are made of heat moldable EVA. They are comfortable and thin so they don't take up too much space in your boot. The edges are curved and thin so that there is a seamless transition between the innersole and your boot liner.

Buy Now